한국어 English Chinese Russian

펌웨어 변경이력 / 다운로드


제품선택

CSE-M32, CSE-H20, CSE-H21 펌웨어 변경이력

배포일[버전] 변경내용
2016-03-16[2.0A] 1. 텔넷 콘솔 기본 비밀번호 적용.
2. 텔넷 옵션 및 비밀번호 처리관련 버그 수정.
2016-02-18[1.4B] 1. DNS 소스포트 변경(53 -> 4096 ~ 65535사이 랜덤 값)
2. TCP 서버/클라이언트 모드 관련 버그 수정
3. 인증서 시그니쳐 해시 알고리즘 변경(MD5 > SHA1)
4. RS422/485일 때 TELCOM 지원
2014-12-29[1.4A] 1. 새 CPU 버전 적용
2. DHCP, DNS, SSL및 RFC2217관련 버그 수정
3. RFC2217 및 DDNS관련 기능 개선
4. 구분자 기능 지원
5. FIFO 사용 안함 옵션 제거
6. AT+PLS명령어 지원

2011-07-26[1.3C] 1. Serial Manager Protocol 버그 수정
2. comment debugging flag related to PPP
3. PPPoE align 버그 수정
4. FIFO 옵션 해제 가능 추가
5. telnet 비밀번호 버그 수정
6. UDP 패킷 블럭 설정 버그 수정
7. 시리얼 버퍼 수정
8. UDP zero checksum 버그 수정
9. ATC ESC character 버그 수정
10. DDNS 응답 파싱
11. DTR/DSR port 버그 수정
12. telnet No Operation command 버그 수정
13. AT+PPNG(ping test) 명령어 추가
14. FIFO 사이즈 줄임 (5ms <- 100ms)
15. ezManager에 DDNS 상태필드 추가
16. ezManager에 MAC 주소필드 추가
2009-07-07[1.3A] 1. dynamic TCP session management support
2. modified - tcp.c winq.c tty.c iptrap.c lsh.c scfg.c init.c
3. add 'length field' to env write len
4. CN0/CN1 led bug fix at U2S mode
5. add lsh sc(session control) command
6. limit tcp mss to MIN(TCP_LOCAL_MSS, ppp_send_mru, ppp_recv_mru)
7. add arp table field to ezManager status
8. decrease sio buffer to 3840 from 4096 to avoid ddns out of memory
9. ATC CN0/CN1 led bug fix
10. DNS peer_ip (ATC mode) bug fix
11. add AT+PSE(send escape) command
12. mac_id support
2009-03-04[1.2H] 1. UDP(at U2S mode) multicast support
2. duplicate exponential retransmit timer bug fix
3. reset rto_count in func tcp_stop_timers()
4. telcom | break support
5. telcom | reply SET_CONTROL request
6. telcom | avoid enabling hardware flow control
7. U2S dynamic peer_ip/port update
8. telcom | RTS collision bug fix
9. telnet sio dump support (add sd command)
10. rename sio0/sio1 to com1/com2
2009-01-20[1.2G] 1.decrease rx idle time to 10bit long
2.IP change missing TCP name bug fix
3.avoid connection to zero IP (0.0.0.0)
4.ata hook bug fix
5.lsh passwd buf overflow bug fix
2008-12-01[1.2F] 1.add atc command PPID & PPPW
2.reload env if crc test is failed when scfg write
3.atcmd auto_ns on/off support
4.blink led (rx/tx) if fatal env fault found
5.emac | reset rx_bds if RX buffer is full
2008-11-13[1.2E] 1.freeze link led blink
2.DTR/RTS update on telcom notify
3.atcmd host name lookup support (+pnip,+prhn)
4.TCP no delay support
5.TX delay support (up to 25 character time)
6.drop late dhcp response from coexist dhcp server
7.ezManager | TCP session management support
8.ezSerialConfig support / ISP operation change same as H80
9.add WDT reset code at emac wait loop to avoid H21 mulfunction
10.telcom 0xff bug fix
11.disable dhcp unicast
12.at dial hook bug fix
13.avoid at+pdc/ppe both enabled
2008-08-05[1.2D] 1. boot up checking H21 identification pin
2. fix telnet login message
2008-06-30[1.2C] 1. IP Change Trap - UDP bug fix
2. SSL/SSH telnet bug fix
3. modify SSL/SSH command lock
4. sio mark/space support
5. duplicate local port bug fix
2008-06-10[1.2B] 1. modify ddns update period
2008-05-29[1.2A] 1. SSL/SSH support
2. disable UDP dest_ip comparison when ezl_local_ip is zero
3. TCP MSS bug fix
4. U2S net_tx, net_rx update bug fix
5. add ICMP frag needed message processing routine
6. duplicate peer name bug fix
7. expand mfa free size to avoid lsh_printf malloc fail
8. optimization option change -O2 to -Os (reduce code size near 10k)
2008-01-16[1.1G] 1. tcp urg pointer bug fix
2. dhcpc sends broadcast if server is not in subnet
2008-01-15[1.1F] 1. dynamic IP telnet support
2. lsh series command bug fix
3. add arp refresh code in lookup.c iptrap.c u2s.c
2007-12-26[1.1E] 1. ip change trap support
2. modify emac_init() for new PHY LAN8700
3. set PHY s/w-reset timeout to 500ms
2007-11-16[1.1D] 1. is_ip_broadcast() 0xe0 comparison bug fix
2. is_ip_broadcast() broadcast detection bug fix
2007-09-15[1.1C] 1. add CTS & PDC_PTSR monitoring loop
2007-09-12[1.1B] 1. Dynamic DNS(DDNS) support.
2. DNS stat->end comparison bug fix.
3. PPP down bug fix.
2007-08-22[1.1A] 1. seq_gap bug fix.
2. emac TBQP bug fix.
3. reply none zero length keep-alive.
4. reset processor after ezcfg write.
2007-08-10[1.0E] 1. RTS vibration bug fix.
2. intr pending bug fix by setting AIC protect mode.
3. receive time-out frame loss bug fix.
4. PDC start_tx atomic bug fix.
2007-07-24[1.0D] 1. Telnet COM port control option support.
2007-07-03[1.0B] 1. Expand FIFO size.
2. UART 1.5/2 stop bits bug fix.
3. sio_rx_fifo_max bug fix.
2007-04-12[1.0A] 1. Initial touch.


CIE-H10(A), CIE-M10(A), CIE-H12(A), CIE-H14(A) 펌웨어 변경이력

배포일[버전] 변경내용
2020-10-15[2.2B] 1. PHY 초기화 로직 변경
2020-04-22[2.2A] 1. A시리즈용 펌웨어: CIE-H10A/M10A/H12A/H14A
2. 인텔칩셋 Ethernet 카드와의 호환성 문제 해결
3. 현재상태보기에 부트버전 표시
4. 기타 사소한 버그 수정
2020-02-21[2.1B] 1. 일부 사소한 버그 수정
2019-08-02[2.1A] 1. CIE-H10A/M10A/H12A/H14A 지원
2. 이메일 알림기능 동작 방식 개선
3. IP주소 유효성 검사 로직 개선
4. AT명령모드 명령어 추가: ATV2
5. GARP 기능 개선
6. RFC3168 지원
7. 기타 사소한 버그 수정
2016-03-21[2.0A] 1. 텔넷 콘솔 기본 비밀번호 적용.
2. 텔넷 옵션 및 비밀번호 처리관련 버그 수정.
2016-01-29[1.6B] 1. DNS 소스포트 변경(53 -> 4096 ~ 65535사이 랜덤 값)
2. CIE-M10 TXDE 시그널 지원
3. 디버깅 로그보기에 Modbus/TCP 메세지 확인기능 추가
2014-12-29[1.6A] 1. 새 CPU 버전 적용
2. 모드버스/TCP 관련 기능 추가(FC 43/14)
3. HTTP 및 DHCP관련 버그 수정
4. HTTP 기능 개선
5. RFC2217 기능 개선
6. UDP모드에서 구분자기능 지원
2013-08-14[1.5A] 1. CIE-H14 지원
2. HTTP 펄스 제어 태그 지원
3. 출력포트 상태 초기화 기능 지원
4. E-mail 알림 기능 지원 (CIE-H12/H14만 지원)
5. 구분자 기능 지원
6. HTTP 응답속도 개선
7. AT명령모드 AT+PLS 명령어 지원
8. 기타 버그 수정
2011-07-27[1.4B] 1. 신제품(CIE-H12) 지원
2. TCP 세그먼트 사이즈 조정 (winq_size/2)
3. Modbus/TCP 다중접속 기능 추가 (최대 8개 세션)
4. AT명령모드 명령어 (PPNG) 추가
5. TELNET No operation 에 대한 이상응답 오류 수정
6. UDP 0 Checksum 에 의한 오류 수정
7. PPPoE AC-Name 필드 값 관련 오류 수정
8. Modbus/TCP Class 1 함수(코드 1, 2, 4, 5, 6, 7) 추가 지원
9. Modbus/TCP Class 2 함수(코드 15) 추가 지원
10. Modbus/TCP 함수(코드 105) 추가 지원
11. Exception Status 코드 6번 추가
12. 시리얼포트 0 FIFO 사이즈 관련 오류 수정
13. 동시 다발적 입력포트 변경 알림 기능 사용에 의한 오류 수정
14. 현재상태보기 정보 추가 (MAC주소, DDNS 응답 메시지)
15. AT명령모드 ESC 케릭터 설정 관련 오류 수정
16. TCP Fast retransmit 관련 오류 수정
17. 시리얼설정모드 잘못 된 프레임 설정 관련 오류 수정
18. 유효하지 않은 Modbus/TCP 헤더 길이 관련 오류 수정
19. Modbus/TCP 데이터 수신 유실에 관한 오류 수정
20. 매크로 및 펄스 제어관련 HTTP 403응답 코드 추가
21. 매크로모드 포트 별 설정기능 추가
22. UDP 패킷 블록설정 동작 오류 수정
23. TELNET 로그인 시 비밀번호 입력 관련 오류 수정
24. FIFO 사용/사용 안 함 옵션 추가
25. 일부 큐(queue) 사이즈 조정
> HTTP(1460->512), Mbus(768->384), sio0(6144->4096), tty(2048->1024)
26. 시리얼포트 수신 버퍼 사이즈 수정(4096->2048)
27. HTTP 동시 세션 최대 개수 수정(4->8)
28. Modbus/TCP 주소 체계 수정(byte -> word)
29. ARP테이블 크기 조정(4->16)
30. AT명령모드에서 유효하지 않은 명령 파라메터 관련 오류 수정
31. 시리얼설정모드에서 유효하지 않은 명령 파라메터 관련 오류 수정
32. H12 시리얼설정모드 진입 시도 오류 수정
33. HTML 다운로드 관련 오류 수정
2009-08-31[1.3E] 1. 401 reply string bug fix
2009-07-10[1.3D] 1. sio0 PDC_tx on DSR bug fix
2. http flushing peer bug fix
3. add lsh sc(session control) command
4. limit tcp mss to MIN(TCP_LOCAL_MSS, ppp_send_mru, ppp_recv_mru)
5. add arp table field to ezManager status
6. DNS peer_ip (ATC mode) bug fix
7. add AT+PSE(send escape) command
8. mac_id support
9. disable HTTP/Modbus output update if macro is enabled
2009-06-11[1.3C] 1. http winq overflow bug fix
2. add 'struct tcp' arg inside tcp->notify_sent/rcvd paramenter
3. M10/H10 product message bug fix
2009-05-21[1.3B] 1. Modbus read multiple regs byte ordering bug fix.
2. 'brace in string' bug fix.
2009-04-24[1.3A] 1. webpage script support
2. dynamic TCP session management support
3. modified - tcp.c winq.c tty.c iptrap.c lsh.c scfg.c init.c
4. add 'length field' to env write len
2008-07-30[1.2C] 1. IP Change Trap - UDP bug fix
2. sio mark/space support
3. duplicate local port bug fix
2008-06-10[1.2B] 1. modify ddns update period
2008-05-30[1.2A] 1. dynamic memory management support
2. disable UDP dest_ip comparison when ezl_local_ip is zero
3. TCP MSS bug fix
4. U2S net_tx, net_rx update bug fix
5. add icmp frag needed message processing routine
6. add IO comment facility over http
2008-02-05[1.1F] 1. tcp urg pointer bug fix
2. dhcpc sends broadcast if server is not in subnet
2008-01-14[1.1E] 1. ip_trap(DDNS/TCP/UDP) support
2. dynamic IP telnet support
3. lsh series command bug fix
4. add arp refresh code in lookup.c iptrap.c u2s.c
5. add http port number field
2007-11-16[1.1D] 1. add CTS & PDC_PTSR monitoring loop
2. is_ip_broadcast() 0xe0 comparison bug fix
3. is_ip_broadcast() broadcast detection bug fix
2007-09-12[1.1C] 1. Dynamic DNS(DDNS) support
2. DNS stat->end comparison bug fix
3. PPP down bug fix
2007-08-29[1.1B] 1. telnet com port control option support
2. reply none zero length keep-alive
3. reset processor after ezcfg write
2007-08-23[1.1A] 1. seq_gap bug fix
2. emac TBQP bug fix
3. disable H/W flow-control
4. RTS vibration bug fix
5.intr pending bug fix by setting AIC protect mode
6. receive time-out frame loss bug fix
7. PDC start_tx atomic bug fix
8. infinite PDC tx intr bug fix
2007-07-06[1.0B] 1. Infinite RST bug fix
2. Stopbit bug fix
2006-04-12[1.0A] 1. Initial touch.


EZL-50M, EZL-60M 펌웨어 변경이력

배포일[버전] 변경내용
2016-08-24[1.3A] 1. AT 명령어 추가 (+PPE, +PPID, +PPPW, +PBR)
2. TCP 기능 개선
3. 기타 버그 수정
2010-04-22[1.2E] 1. 접속종료 대기시간 관련 버그 수정
2. 잘못된 IP주소(0.0.0.0)사용에 따른 처리과정 추가
3. UDP 패킷 블록설정에 대한 미세 오동작 수정
4. 시스템 타이머 만료 시 처리과정 추가
5. ATC 모드에서 접속 후 TCP 데이터 프레임 나뉨현상 수정
6. 랜 칩 초기화 과정 중 타이밍 오차로 인한 LINK LED 동작 버그 수정
2010-01-14[1.2D] 1. support 2 stop bits
2. handling bad environment parameters
2009-09-18[1.2C] 1.serial mark/space parity support
2. support mac_id, no_delay, sio_rx_drop
3. U2S dynamic peer_ip/port update bug fix
2009-08-21[1.2B] 1. Factory reset bug fix : comment
2. modify ip_smart_update : load new subnet mask
3. add atc command : +PSE
4. modify PPP_MRU size
5. apply COD_SEND_ETH_ADDR option to all ezTCP Mode except U2S
6. modify minimum Ethernet frame size 62 -> 60
7. flush Ethernet frame PAD
8. sio1 rx interrupt bug fix
2009-03-27[1.2A] 1. modify TCP STATE MACHINE
2. add Product ID in F/W
3. support U2S echo
4. tcp_rto_count reset bug fix
5. add Power Down option : default disable
2008-12-11[1.1L] 1. ATC Serial RX update bug fix
2. xfer_timeout bug fix if tcp peer zero window
2008-10-23[1.1k] 1. tx_slow support : 200us delay
2. support RESET and Close TCP by ezcfg
3. rebuild dhcp machine
4. modify sio sending method in U2S mode
5. avoid sending udp datagram if header only
6. add seed number generation routine
7. modify tcp_local_port load method
8. U2S interval bug fix
2008-08-07[1.1j] 1. add RTL8019 RX ring buf overflow handler
2. rebuild RTL8019 reset sequence and internal ring buf
2008-05-15[1.1I] 1. add atc command : +ppng
2. avoid sending ARP request if target IP is zero
3. avoid sending packet if target MAC is zero
4. xfer_timeout bug fix
2007-09-13[1.1H] 1. UDP multicast support
2. PPP down bug fix
2007-06-13[1.1G] 1. Initial release.


EZL-50, EZL-60-T2S,ATC,COD,U2S 펌웨어 변경이력

배포일[버전] 변경내용
2005-10-26[1.7H] 1. PPPoE rcvd_udp_hdr bug fix
2005-09-07[1.7G] 1. Support VDSL
2005-07-06[1.7F] 1. PPPoE MRU NAK support
2004-04-22[1.7B] 1. ezcfg X2 mode bug fix
2003-11-19[1.6C] 1. IP filtering support
2. ezConfig TCP state view support
2002-11-04[1.4H] 1. XON/XOFF support
2. U2S multi-cast support
2002-07-24[1.4A] 1. U2S mode support


EZL-50L, EZL-60L, EZL-70, EZL-200L 펌웨어 변경이력

배포일[버전] 변경내용
2016-08-24[1.3A] 1. RFC3168 지원 : ECN 지원 안 함으로 동작
2. AT 명령어 추가 (+PPE, +PPID, +PPPW, +PBR)
3. TCP 기능 개선
4. 기타 버그 수정
2010-04-22[1.2E] 1. 접속종료 대기시간 관련 버그 수정
2. 잘못된 IP주소(0.0.0.0)사용에 따른 처리과정 추가
3. UDP 패킷 블록설정에 대한 미세 오동작 수정
4. 시스템 타이머 만료 시 처리과정 추가
5. ATC 모드에서 접속 후 TCP 데이터 프레임 나뉨현상 수정
6. 랜 칩 초기화 과정 중 타이밍 오차로 인한 LINK LED 동작 버그 수정
2010-01-15[1.2D] 1. support 2 bits stop bit
2. handling bad environment parameters
2009-09-18[1.2C] 1. serial mark/space parity support
2. support mac_id, no_delay, sio_rx_drop
3. U2S dynamic peer_ip/port update bug fix
2009-08-20[1.2B] 1. Factory reset bug fix : comment
2. modify ip_smart_update : load new subnet mask
3. add atc command : +PSE
4. modify PPP_MRU size
5. apply COD_SEND_ETH_ADDR option to all ezTCP Mode except U2S
6. modify minimum Ethernet frame size 62 -> 60
7. flush Ethernet frame PAD
8. sio1 rx interrupt bug fix
2009-02-18[1.2A] 1. support factory reset(EZL-200L)
2. modify TCP STATE MACHINE
3. support network packet load scan operation mode(EZL-200L)
4. Power Down option : default disable
5. add Product ID in F/W
6. support U2S echo
7. tcp_rto_count reset bug fix
2008-11-10[1.1L] 1. ATC Serial RX update bug fix
2. xfer_timeout bug fix if tcp peer zero window
2008-10-23[1.1K] 1. tx_slow support : 200us delay
2. support RESET and Close TCP by ezcfg
3. rebuild dhcp machine
4. modify sio sending method in U2S mode
5. avoid sending udp datagram if header only
6. add seed number generation routine
7. modify tcp_local_port load method
8. U2S interval bug fix
2008-07-29[1.1J] 1. add RTL8019 RX ring buf overflow handler
2. rebuild RTL8019 reset sequence and internal ring buf
2008-05-15[1.1I] 1. use a fake window size for the MSS bug of MS Vista
2. add atc command : +ppng
3. avoid sending ARP request if target IP is zero
4. avoid sending packet if target MAC is zero
5. xfer_timeout bug fix
2007-09-13[1.1H] 1. UDP multicast support
2. PPP down bug fix
2006-09-13[1.1G] 1. sio rx idle time(10~20ms) detection support
2. external SRAM bug fix
2006-03-22[1.1F] 1. flowctrl bug fix in ATC mode
2. verify EEPROM after ezcfg write
3. T2S IP filtering support
4. TCP keep-alive bug fix
2006-02-22[1.1E] 1. ezl-70 support, rx/tx/link led control
2005-09-21[1.1D] 1. discard sio_rx data during idle state in t2s mode
2005-09-13[1.1C] 1. shrink RTL8019 RX ring buffer
2005-09-08[1.1B] 1. add DHCP client_id option, and modify ip_update for VDSL
2005-07-25[1.1A] 1. real-time debug message on/off
2. boot time STS LED blink
3. delay 10ms after at+pwp command
4. drop DHCP packet if DHCP is not configured
2005-07-11[1.0G] 1. avoid sending TCP/UDP segment if IP not allocated
2. ATC/COD dhcp arp bug fix
3. call arp_boot_announce after DHCP IP allocation
4. call arp_boot_announce in init.c
5. remove EZL-50L pppoe ID/PWD debug code(constant ID/PWD)
6. ezl_gate_ip atomic bug fix
2005-07-01[1.0F] 1. rtl8019 drop bug fix (page header problem)
2. 30 second idle reset rtl8019


EZL-200F / EZL-300S 펌웨어 변경이력

배포일[버전] 변경내용
2009-07-13[1.3J] 1. multi-connection RS422/485 support
2. rdb password bug fix
2009-01-15[1.3I] 1. S/W ethernet tx crc32 generation
2. remove mic_rt_direct/mic_rt_default in module.c
3. rename rt_default/direct to mic_rt_default/direct in route.c
4. ezcfg invalid dhcp gate_addr bug fix due to above 2 changes
2008-11-12[1.3H] 1. keep-alive reply bug fix
2008-07-14[1.3G] 1. increase IDLE_STK_SIZE to avoid stack overflow
2008-06-25[1.3F] 1. parity mark/space support
2. dhcp DHCP_OPT_PARM_REQ option bug fix
2008-03-27[1.3E] 1. add t2smc keep alive & timeout
2007-11-06[1.3D] 1. ssh empty server_key bug fix
2. cross-compiler change 3.4.1 -> 4.1.0
2007-08-10[1.3C] 1. keep-alive reply bug fix
2006-12-13[1.3B] 1. SLIP bridge support
2. emac burst broadcast bug fix
2006-03-20[1.3A] 1. SSH support
2005-12-26[1.2F] 1. drop broadcast TCP
2. add DHCP client_id option for VDSL
3. EAPOL support
2005-07-15[1.2D] 1. 422/485 COD bug fix
2. 422/485 status rx/tx bytes bug fix
2005-05-25[1.2A] 1. remote ezConfig support
2. burst frame rx bug fix
3. TCP option misalignment bug fix
2005-05-23[1.1G] 1. if duplicate IP address detected, log it and restart ARP announce
2005-05-19[1.1F] 1. arp announce at each IP allocation time
2005-05-18[1.1E] 1. start config PPPoE always
2005-05-13[1.1D] 1. SSL zero pad bug fix
2. SSL write_mac type bug fix
3. enable watch dog timer in crt0.S
4. ezcfg status bug(zero gateway) fix
2005-05-05[1.1C] 1. DHCP data mis-align bug fix
2005-04-28[1.1B] 1. set t2s_peer to 1 always
2005-04-04[1.0F] 1. enable watch dog timer
2. answer reboot after firmware update
2005-04-04[1.1A] 1. SSL buffer size bug fix
2005-03-30[1.0E] 1. remap direct timer_task call to gate call(timer.c)
2005-03-18[1.0D] 1. pariry exchange fix
2005-03-15[1.0C] 1. XON/XOFF support
2005-03-07[1.0B] initial release
2004-08-10[1.0A] 1. initial touch


EZL-80, EZL-80c, EZL-90, EZL-300L 펌웨어 변경이력

배포일[버전] 변경내용
2008-05-15[1.4G] 1. use a fake window size for the MSS bug of MS Vista
2. add atc command : +ppng
3. avoid sending ARP request if target IP is zero
4. avoid sending packet if target MAC is zero
5. xfer_timeout bug fix
2007-03-29[1.4F] 1. shared key authentication support
2006-04-10[1.4E] 1. add atc command : +psc +psd +pbsd
2. flowctrl bug fix in ATC mode
3. verify EEPROM after ezcfg write
4. T2S IP filtering support
5. TCP keep-alive bug fix
2006-01-16[1.4D] 1. arp cache bug fix on peer mac address change
2005-09-21[1.4C] 1. discard sio_rx data during idle state in t2s mode
2. reset prism after 30sec rx idle
3. increase prism response wait time
2005-09-08[1.4B] 1. add DHCP client_id option, and modify ip_update for VDSL
2005-07-25[1.4A] 1. real-time debug message on/off
2. boot time STS LED blink
3. pull-up RX1 pin (console)
4. delay 10ms after at+pwp
5. drop DHCP packet if DHCP is not configured
2005-07-11[1.3I] 1. avoid sending TCP/UDP segment if IP not allocated
2. ATC/COD dhcp arp bug fix
3. call arp_boot_announce after DHCP IP allocation
4. ezl_gate_ip atomic bug fix
2005-06-16[1.3H] 1. remote ezConfig support
2. comment support
2005-05-20[1.3G] 1. enable createIBSS if target ssid presents
2005-01-26[1.3F] 1. TCP SYN_RCVD bug fix
2005-01-14[1.3E] 1. TCP winq_init bug fix
2005-01-13[1.3D] 1. TCP zero window bug fix
2005-01-06[1.3C] 1. at+prip : arp quick request
2. modify atc +++ processing sequence to be same as ezl-200/50
2004-12-29[1.3B] 1. TCP nagle timer support
2004-12-14[1.3A] 1. TCP sliding window support
2. fix DHCP led blink interval
3. send atc +++ character
2004-12-07[1.2C] 1. config wlan_env over wlan
2004-10-14[1.2B] 1. set EN_XONOFF bit to one while reading eeprom
2004-09-08[1.2A] 1. XON/XOFF flowcontrol support
2004-08-30[1.1H] 1. increase dhcp packet size due to some dhcp server
2004-08-26[1.1G] 1. increase TMP_BUF_SIZE due to some dhcp server
2004-06-29[1.1F] 1. TCP window size bug fix
2004-06-18[1.1E] 1. U2S flow-ctrl bug fix


EZP-250 펌웨어 변경이력

배포일[버전] 변경내용
2008-12-11[3.0G] 1. sio rx idle time(10~20ms) detection support
2. drop rcvd udp datagram if Te2 tx buffer is not available
3. LCP Echo / TCP Keep-Alive default disable
4. modify md5 hash function to avoid stack overflow
5. ID/PW command parameter length bug fix
6. cross-compiler change 3.4.1 -> 4.2.2
7. EEPROM hardware fault detection support
8. add tcp_ref_delay_retransmit option
2008-02-18[3.0F] 1. add script processing module
2007-12-11[3.0E] zero ppp_ref_lcp_timeout bug fix
tmp_local_ip bug fix(update tmp_local_ip in ipcp_start)
2007-11-29[3.0D] add tcp_ref_delay_keep_alive option
2006-12-15[3.0C] 1. duplicate 730(UDP SENT) message bug fix
2. US command buffer size bug fix (300->256)
3. hdlc rx buffer full limit bug fix
2006-07-24[3.0B] 1. apply ppp_ref_lcp_count to code (LCP & IPCP)
2005-08-17[3.0A] 1. initial release


EZU-100 펌웨어 변경이력

배포일[버전] 변경내용
2010-10-21[3.2E] 1. CMOTECH CBU-450D 모뎀 지원
2. SCDi SEM-W220 모뎀 지원
3. 텔넷 클라이언트 기능 지원 안 함
4. KTFT EV-HM100 모뎀 지원 안 함
2010-03-16[3.2D] 1. CHU-629K 모뎀(KT i-plug) 지원
2010-02-26[3.2C] 1. Sending a huge UDP packet bug with US command has been fixed.
2. Abnormal working after 492 days after running has been fixed.
3. SAMSUNG SPH-H1300 has been supported.
4. TP(TE2 Parity), TS(TE2 Stop bit) and TD(TE2 Data bit) commands have been added.
5. Configuration fail bug of SKY IM-H100 modem has been fixed.
2009-10-14[3.2B] 1. Supports CHU-629S HSDPA modem
2. Add the SC(Send Comment) command.
2009-08-13[3.2A] 1. KTFT EV-HM100 new firmware support
2. KTFT EV-HM100 support
3. add tcp_ref_delay_retransmit option
4. change default tcp retransmit delay : 500ms -> 2s
5. add tcp_ref_delay_keep_alive option
6. EEPROM hardware fault detection support
7. ID/PW command parameter length bug fix
8. sio0(TE2) rx idle time(10~20) detection support
9. drop rcvd udp datagram if sio0(TE2) tx buffer is not available
10. LCP Echo / TCP Keep-Alive default disable
11. modify md5 hash function to avoid stack overflow
12. add Product ID in F/W
13. modify TCP STATE MACHINE
14. cross-compiler change 3.4.1 -> 4.2.2
2007-10-04[3.1H] 1. CMOTEC, Anydata HSDPA modem support.
2. TB Command (3.1E)
2007-02-15[3.1B] 1. wait 500ms before USB power on
2. power off USB port 1
3. set ClearPortEnable before power off
2006-09-25[3.1A] 1. arrange & stabilize TD232LP/USB stack
2005-07-18[3.0A] 1. initial touch


EZL-50R-T2S,ATC,COD,U2S 펌웨어 변경이력

배포일[버전] 변경내용
2005-09-07[2.0E] 1. Support VDSL
2005-07-06[2.0D] 1. PPPoE MRU NAK support
2005-01-07[2.0B] 1. activate EEPROM major/minor field
2004-11-26[2.0A] 1. EZL-50R release, Never download to ezl50A!!!!


EZL-410, EZL-400S 펌웨어 변경이력

배포일[버전] 변경내용
2009-09-18[2.1B] 1. fixed a bug about wireless LAN link
2. drop multicast packet
2009-02-20[2.1A] 1. S/W Ethernet tx crc32 generation
2. routing table bug fix
3. keep-alive bug fix
4. stack overflow bug fix
5. dhcp option bug fix
6. cross-compiler change
2006-12-13[2.0I] 1. emac burst broadcast bug fix
2006-08-03[2.0G] 1. fix INCLUDE_NAT mistake
2006-07-12[2.0F] 1. crypto_xxx_key() bug fix
2. rng initialization bug fix
3. add env 'ver' command
2005-12-21[2.0E] 1. add env_ext options
2005-12-01[2.0D] 1. ATC SSL accept bug fix
2005-11-02[2.0C] 1. EAPOL support
2. arp announce bug fix
3. ATC source IP(in multi-ip) bug fix
4. COD water mark bug fix
5. U2S source IP(in multi-ip)
6. broadcast recv bug fix
7. sio parity bug fix
2005-10-26[2.0B] 1. enable SSL, comment
2005-10-11[2.0A] 1. initial release


CSP-H50 펌웨어 변경이력

배포일[버전] 변경내용
2010-10-21[3.2E] 1. CMOTECH CBU-450D 모뎀 지원
2. SCDi SEM-W220 모뎀 지원
3. KTFT EV-HM100 모뎀 지원 안 함
2010-03-12[3.2D] 1. CHU-629K 모뎀(KT i-plug) 지원
2010-02-08[3.2C] 1. handle sysclk overwrap
2. SAMSUNG SPH-H1300 support
3. add TP(None, Even, Odd), TD(7,8), TS(1,2) command
4. support DUAL peer host: add SA, TC command
5. fix SKY IM_H100 configuration bug it happen 3.2B firm
2009-10-14[3.2B] 1. Supports CHU-629S HSDPA modem
2. Add the SC(Send Comment) command.
2009-08-13[3.2A] 1. KTFT EV-HM100 new firmware support
2. KTFT EV-HM100 support
3. add tcp_ref_delay_retransmit option
4. change default tcp retransmit delay : 500ms -> 2s
5. add tcp_ref_delay_keep_alive option
6. EEPROM hardware fault detection support
7. ID/PW command parameter length bug fix
8. sio0(TE2) rx idle time(10~20) detection support
9. drop rcvd udp datagram if sio0(TE2) tx buffer is not available
10. LCP Echo / TCP Keep-Alive default disable
11. modify md5 hash function to avoid stack overflow
12. add Product ID in F/W
13. modify TCP STATE MACHINE
14. cross-compiler change 3.4.1 -> 4.2.2
2007-10-04[3.1H] 1. CMOTECH, Anydata HSDPA modem support
2007-07-13[3.1E] 1. initial release


CSE-M73(A), CSE-H25 펌웨어 변경이력

배포일[버전] 변경내용
2020-04-24[2.2A] 1. 인텔칩셋 Ethernet 카드와의 호환성 문제 해결
2. 현재상태보기에 부트버전 표시
3. 기타 사소한 버그 수정
2020-01-10[2.1A] 1. CSE-M73A 지원
2. IP주소 유효성 검사 로직 개선
3. 보안 기능 개선(TLS v1.1/1.2 지원 및 SSL v2.0/3.0 삭제)
4. AT명령모드 명령어 추가: ATV2
5. GARP 기능 개선
6. RFC3168 지원
7. 기타 사소한 버그 수정
2016-03-16[2.0A] 1. 텔넷 콘솔 기본 비밀번호 적용.
2. 텔넷 옵션 및 비밀번호 처리관련 버그 수정.
2014-12-29[1.7A] 1. 새 CPU 버전 적용
2. DHCP, DNS, SSL및 RFC2217관련 버그 수정
3. RFC2217 기능 개선
4. UDP모드에서 구분자 기능 지원
2012-12-05[1.6A] 1. 다중접속 세션 확장(3ch -> 8ch)
2. 구분자 기능 추가
3. FIFO 옵션 제거
4. SSL 관련 버그 수정
5. 잘못 된 IP주소 설정 감지 기능 추가
6. MAC ID 기능 SSL에서 지원
7. RS422/485 포트 SSL에서 사용 가능
8. AT+PLS (link status) 명령어 지원
9. DDNS 모듈 변경 (checkip 기능 추가)
10. UDP DNS관련 버그 수정
2011-07-26[1.5D] 1. SCFG 새로운 필드 쓸수 있게 수정
2. SCFG 다중 명령어 지원
3. SCFG K(check) 명렁어 추가
4. SCFG check code/id/length field of writing frame
5. 디버그 모드에서 PPPoE IP 할당 버그 수정
6. FIFO 옵션 해제 가능 추가
7. telnet 비밀번호 버그 수정
8. UDP 패킷 블럭 설정 버그 수정
9. RS422/485 slow_tx 버그 수정
10. SCFG frame 버그 수정
11. SSL rxq full 버그 수정
12. SSL 윈도우 사이즈 버그 수정
13. TCP 재전송 버그 수정
14. PPPoE align 버그 수정
15. UDP zero checksum 버그 수정
16. ATC ESC character 버그 수정
17. DDNS 응답 패킷 처리 기능 보완
18. telnet No Operation command 버그 수정
19. AT+PPNG(ping test) 명령어 추가
20. ezManager에 DDNS 상태 필드 추가
21. ezManager에 MAC 주소 필드 추가
22. CSE-H25 DTR/DSR/DCD/RI 포트 지원
2009-07-23[1.5A] 1. dynamic TCP session management support
2. modified - tcp.c winq.c tty.c iptrap.c lsh.c scfg.c init.c
3. add 'length field' to env write len
4. add lsh sc(session control) command
5. limit tcp mss to MIN(TCP_LOCAL_MSS, ppp_send_mru, ppp_recv_mru)
6. add arp table field to ezManager status
7. DNS peer_ip (ATC mode) bug fix
8. add AT+PSE(send escape) command
9. mac_id support
10. blink status LED after entering scfg mode
11. disable com2 access by sd command
2008-12-11[1.4D] 1. decrease rx idle time to 10bit long
2. IP change missing TCP name bug fix
3. avoid connection to zero IP (0.0.0.0)
4. ata hook bug fix
5. lsh passwd buf overflow bug fix
2008-12-02[1.4C] 1. add atc command PPID & PPPW
2. reload env if crc test is failed when scfg write
3. atcmd auto_ns on/off support
4. blink led (rx/tx) if fatal env fault found
5. emac | reset rx_bds if RX buffer is full
2008-10-16[1.4B] 1. DTR/RTS update on telcom notify
2. atcmd host name lookup support (+pnip,+prhn)
3. TCP no delay support
4. TX delay support (up to 25 character time)
5. drop late dhcp response from coexist dhcp server
6. telcom 0xff bug fix
7. disable dhcp unicast
8. at dial hook bug fix
9. avoid at+pdc/ppe both enabled
2008-07-18[1.4A] 1. TTL output support - H/W fix
2008-06-30[1.3C] 1. IP Change Trap - UDP bug fix
2. SSL/SSH telnet bug fix
3. modify SSL/SSH command lock
4. sio mark/space support
5. duplicate local port bug fix
2008-06-10[1.3B] 1. modify ddns update period
2008-05-29[1.3A] 1. SSL/SSH support
2. disable UDP dest_ip comparison when ezl_local_ip is zero
3. TCP MSS bug fix
4. U2S net_tx, net_rx update bug fix
5. add ICMP frag needed message processing routine
6. optimization option change -O2 to -Os (reduce code size near 10K)
2008-02-05[1.2D] 1. initial release


CSW-H80 펌웨어 변경이력

배포일[버전] 변경내용
2016-04-21[2.0A] 1. 텔넷 콘솔 기본 비밀번호 적용
2. 텔넷 옵션 및 비밀번호 처리관련 버그 수정
3. DHCP, DNS 및 RFC2217관련 버그 수정
4. RFC2217 기능 개선
5. DNS 소스 포트 변경 (53 -> 49152 ~ 65535 사이 임의 값)
6. FIFO 사용 안함 옵션 제거
7. WPA2-TKIP, WPA2-TKIP/AES, WPA-AES, WPA-TKIP/AES 지원
(기존 펌웨어는 WPA-TKIP, WPA2-AES만 지원)
2011-07-26[1.1H] 1. FIFO 옵션 해제 가능 추가
2. telnet 비밀번호 버그 수정
3. Serial Manager Protocol 버그 수정
4. ezPairing 버그 수정
5. PPPoE align 버그 수정 (디버깅 모드)
6. UDP 패킷 블럭 설정 버그 수정
7. PPPoE align 버그 수정
8. UDP zero checksum 버그 수정
9. ATC ESC character 버그 수정
10. DDNS 응답 패킷 처리 기능 보완
11. telnet No Operation command 버그 수정
12. AT+PPNG(ping test) 명령어 추가
13. ezManager에 DDNS 상태필드 추가
14. ezManager에 MAC 주소필드 추가
15. not set secure bit for WPA
16. power table 지원
17. set secure bit in key msg 4 of 4 for WPA/WPA2
18. EAPOL V2 frame 허용
19. DHCP 77 옵션 지원 (user class info)
20. tcp segment 줄임 (under winq_size/2)
21. 전송지연기능 사용안함 추가
22. sc(session control) 명령어 추가
23. ezManager에 arp table 필드 추가
24. DNS peer_ip (ATC mode) 버그 수정
25. AT+PSE(send escape) 명령어 추가
26. MAC 주소 전송 기능 추가
2009-05-07[1.1A] 1. make ibssid individual & local mac address
2. UDP(at U2S mode) multicast support
3. duplicate exponential retransmit timer bug fix
4. reset rto_count in func tcp_stop_timers()
5. U2S dynamic peer_ip/port update
6. telnet sio dump support (add sd command)
7. dynamic TCP session management support
8. modified - tcp.c winq.c tty.c iptrap.c lsh.c scfg.c init.c
9. WPA/WPA2 PSK support
10. update scfg reason code
11. add 'length field' to env write len
12. rescan & update channel info when AP is not found in bss list
13. disable send modemstate on tcp connection
14. identify product id by csw_pid
2008-12-11[1.0B] 1. Iinitial release


EZI-10 펌웨어 변경이력

배포일[버전] 변경내용
2011-06-30[1.0D] 1. Fragmentation 관련 오류 수정
2. 비트별 제어를 위한 함수(코드 1, 2, 4, 5, 6, 7) 추가
3. 비트별 제어를 위한 함수(코드 15) 추가
4. 펄스 출력을 위한 함수(코드 105) 추가
5. Modbus/TCP 헤더 길이 관련 오류 수정
2010-05-06[1.0C] 1. 고정 IP 설정시 env 블럭 (서브넷 마스크 및 게이트웨이) 설정 오류 수정
2010-03-04[1.0B] 1. 최초 배포


CSE-M53, CSE-H53, CSE-H55 펌웨어 변경이력

배포일[버전] 변경내용
2019-12-10[2.1A] 1. IP주소 유효성 검사 로직 개선
2. AT명령모드 명령어 추가: ATV2
3. GARP 기능 개선
4. RFC3168 지원
5. RFC2217 기능 개선
6. 기타 사소한 버그 수정
2016-03-24[2.0A] 1. 텔넷 콘솔 기본 비밀번호 적용.
2. 텔넷 옵션 및 비밀번호 처리관련 버그 수정.
3. RFC2217 관련 버그 수정
4. DHCP Client 버그 수정
2013-03-14[1.0G] 1. AT 명령어 버그 수정
2012-11-09[1.0F] 1. RS485 수신 버그 수정
2011-07-26[1.0E] 1. PPPoE 버그 수정
2. UDP zero checksum 버그 수정
3. ATC ESC character 버그 수정
4. DDNS 응답 패킷 처리 기능 보완
5. telnet No Operation 버그 수정
6. AT+PPNG(ping test) 명령 추가
7. ezManager status에 ddns 상태표시 추가
8. ezManager status에 mac address 표시 추가
9. custom mac address 지원
10. FIFO 인터럽트 간격 수정
11. SCFG corrupted frame 버그 수정
12. TCP 빠른 재전송 시 버그 수정
13. telnet password 불일치 버그 수정
14. U2S water mark 버그 수정
15. serial config 입력 시 새로운 필드 허용
16. serial config multiple 명령어 지원
17. serial config K 명령어 추가
18. serial config 입력 시 code/id/length field 체크
19. PPPoE 디버깅 코드에서의 버그 수정
2010-05-25[1.0C] 1. PLL 클럭 동작 안정화 (초기화 과정 수정)
2009-11-02[1.0A] 1. Initial Release


CSW-M83, CSW-M85, CSW-H85, CSW-B85 펌웨어 변경이력

배포일[버전] 변경내용
2024-03-05[2.5B] 1. 간헐적으로 무선랜 기능이 멈추는 버그 수정
2. 특정 조건에서 TCP 접속 지연 버그 수정
3. 기타 마이너한 버그 수정
2020-09-09[2.5A] 1. 부적합한 deauth패킷 수신 현상 해결
2. IP주소 유효성 검사 로직 개선
3. 기타 사소한 버그 수정
2018-01-29[2.4B] 1. KRACK 보안이슈에 따른 패치
2. 신규 AT명령(ATV2) 추가: TCP 접속시 IP/PORT 정보 출력
3. 소프트웨어 흐름제어(Xon/Xoff) 기능 추가
4. RFC3168 지원: ECN 사용 안 함
5. GARP(Gratuitous ARP) 전송 방식 개선: 4회 > 11회
6. 기타 사소한 버그 수정
2016-03-25[2.4A] 1. 텔넷 콘솔 기본 비밀번호 적용.
2. 텔넷 옵션 및 비밀번호 처리관련 버그 수정.
2015-12-11[2.3B] 1. DNS 소스포트 변경(53 -> 4096 ~ 65535사이 랜덤 값)
2. 웹 설정 UI 개선
3. 특정 상황에서 국가코드 적용 안되는 버그 수정
2015-01-16[2.3A] 1. USB동글 LED제어기능 추가(M83 Only)
2. RFC2217, DHCP 및 SoftAP기능 관련 버그수정
3. RFC2217 및 DHCP기능 개선
4. UDP모드에서 구분자기능 지원
2013-05-30[2.2B] 1. CSW-M83 지원
- RT5370/RT5390/RT3572(B/G) 칩셋 지원
2. RS485 TXDE 관련 버그 수정
3. DNS 관련 버그 수정
2013-03-15[2.2A] 1. 잘못된 IP주소 설정 감지 기능 추가
2. AT 명령어 버그 수정
3. Hidden SSID인 AP에 접속 안되는 문제 수정
4. SoftAP 모드 기능 향상
5. 텔넷 sd 명령어 지원
2012-10-16[2.1C] 1. 국가 코드 설정기능 추가
2. 웹 설정 기능 추가
3. UDP DNS관련 버그 수정
2012-08-24[2.1B] 1. Soft-AP 버그 수정
2012-07-27[2.1A] 1. WPA-Enterprise 지원(EAP-TLS,TTLS,PEAP)
2. IPv6 지원
3. Soft AP 기능 추가
4. 구분자 기능 추가
2012-05-10[2.0A] 1. 빠른 접속 시간 (V2.0A: 약4초, V1.1A: 약 13초)
2. WPA-PSK/WPA2-PSK 간편 설정: WPA, WPA2, TKIP, AES 등의 파라미터의 세부 설정 필요없음
3. 개선된 Adhoc 기능
4. 개선된 Roaming 기능
5. PHY 고급 설정 기능 추가 (PHY mode, Long/Short Preamble, Long/Short Slot, CTS Protection)
6. 지원 무선랜 모드 변경(802.11b/g/n -> 802.11b/g)
2012-01-11[1.1A] 1. H/W Factory Reset 기능 추가
2. 신호수신강도(RSSI) LED 표시기능 추가
3. WPA-PSK/WPA2-PSK 63바이트 암호문 지원
4. 무선랜 설정 AT명령 추가
2011-11-03[1.0D] - CSW-M85 추가
- 흐름제어 RTS 버그 수정
- RS485 지원
- at+pwp 리셋 버그 수정
- ati3 메시지 버그 수정
- at+prst 명령어 추가
- 펌웨어 이름 변경 기능 추가
- RS422에서 RTS핀 신호 수정
- WPA/WPA2 -> TKIP/AES 종속성 제거
2011-07-26[1.0C] 1. TCP# 핀 버그 수정
2. SCFG 새로운 필드 쓸수 있게 수정
3. SCFG 다중 명령어 지원
4. SCFG K(check) 명렁어 추가
5. SCFG check code/id/length field of writing frame
6. 디버그 모드에서 PPPoE IP 할당 버그 수정
7. 텔넷 비밀번호 버그 수정
8. U2S 모드에서 워터마크 버그 수정
9. telcom RTS/DTR/CTS 핀 버그 수정
10. FIFO 인터럽트 발생 주기 가변적으로 변경
11. 제품 ID 추가
12. SCFG 프레임 버그 수정
13. TCP 재전송 버그 수정
14. ATC 모드에서 ESC character 버그 수정
15. DDNS 응답 패킷 처리 기능 보완
16. ezManager에 DDNS 상태 필드 추가
17. ezManager에 MAC 주소 필드 추가
2011-01-03[1.0A] 1. 최초배포


CSE-M53A 펌웨어 변경이력

배포일[버전] 변경내용
2012-07-12[2.0A] 최초 배포


CSE-T16, CSE-T32, CSE-T48 펌웨어 변경이력

배포일[버전] 변경내용
2023-08-21[1.1B] 1. 환경 값 관련 콘솔 명령어 추가: env net, env cmt, env backup
2. SSH 사용자 아이디 변경: admin -> eztcp
3. 일부 버그 수정
2016-10-05[1.1A] 1. 컴파일러 변경
2. SSH 기능 개선 및 버그 수정
3. 텔넷/SSH 태스크 동작 재 정의
4. 쉘 로그인 기본 비밀번호 변경: admin > sollae
5. UDP모드에서 구분자 기능 지원
6. RFC2217 관련 버그 수정
7. DNS 관련 버그 수정
8. DHCP 관련 버그 수정
2015-01-26[1.0C] 1. RFC2217 기능 개선 (브레이크 시그널 전송 기능 포함)
2. 부팅시간 확인 명령어 지원(st uptime)
3. 제품 리부팅 명령어 지원(reboot)
4. TCP 세션 종료 명령어 지원(sc)
5. 제품 펌웨어 버전 확인 명령어 지원(env ver)
2012-10-23[1.0A] 1. 최초 배포


CSE-M53N, CSE-H53N, CSE-H55N2, CSE-M53NI 펌웨어 변경이력

배포일[버전] 변경내용
2023-11-14[2.3B] 1. 특정 조건에서 TCP 접속 지연 버그 수정
2023-01-17[2.3A] 1. 다중접속 기능 지원 (최대 8채널)
2. AT+PLS 명령 지원
3. RFC2217 기능 개선
4. 기타 사소한 버그 수정
2018-11-30[2.1A] 1. 일부 허브와 링크 연결이 안되는 버그 수정
2. TLS v1.1, TLS v1.2 지원
3. SSL v2.0, SSL v3.0 삭제
4. AT명령모드 명령어 추가: AT+PSSL, ATV2
5. GARP 기능 개선
6. RFC3168 지원
7. 기타 사소한 기능 개선 및 버그 수정
2016-03-18[2.0A] 1. 텔넷 콘솔 기본 비밀번호 적용.
2. 텔넷 옵션 및 비밀번호 처리관련 버그 수정.
2015-12-22[1.1B] 1. DNS 소스포트 변경(53 -> 4096 ~ 65535사이 랜덤 값)
2. U2S 통신모드에서 DTR 시그널 항상 Active
3. 시리얼 300, 600bps 지원
2014-11-28[1.1A] 1. UDP모드에서 구분자기능 지원
2. DHCP관련 버그 수정
3. RFC2217 기능 개선
4. TCP타이머 사용자 설정 기능 지원
2013-11-05[1.0E] 1. SD명령어 지원
2. RS422/485에서 RFC2217지원
3. 마이너 버그 수정
2013-02-14[1.0D] 1. CSE-M53N 지원
2. 7데이터비트 + 패리티 사용 지원
3. 데이터프레임간격 기능 삭제
4. AT명령어 및 RFC2217관련 버그 수정
2012-11-26[1.0C] 1. CSE-H53N 추가
2. RTS/CTS 흐름제어 버그 수정
2012-11-09[1.0B] 1. UDP DNS관련 버그 수정
2012-11-02[1.0A] 1. 최초 배포


PBH-101, PBH-104, PBH-204 펌웨어 변경이력

배포일[버전] 변경내용
2015-10-02[1.1.0] 1. 새로운 상수 추가: PHP_VERSION_ID
2. 새로운 디바이스 추가: NM0/1
3. 새로운 TCP API 추가: TELNET, SSH, 웹 소켓
4. 사소한 버그 수정


CSE-M24 펌웨어 변경이력

배포일[버전] 변경내용
2018-11-30[2.0B] 1. 일부 허브와 링크 연결이 안되는 버그 수정
2. AT명령모드 명령어 추가: ATV2
3. GARP 기능 개선
4. RFC3168 지원
5. 기타 사소한 기능 개선 및 버그 수정
2016-03-21[2.0A] 1. 텔넷 콘솔 기본 비밀번호 적용.
2. 텔넷 옵션 및 비밀번호 처리관련 버그 수정.
3. 시리얼 통신 속도 관련 버그 수정
2015-03-12[1.1A] 최초 배포


CSC-H64 펌웨어 변경이력

배포일[버전] 변경내용
2018-11-30[2.0B] 1. 일부 허브와 링크 연결이 안되는 버그 수정
2. TLS v1.1, TLS v1.2 지원
3. SSL v2.0, SSL v3.0 삭제
4. AT명령모드 명령어 추가: ATV2
5. GARP 기능 개선
6. RFC3168 지원
7. 기타 사소한 기능 개선 및 버그 수정
2016-03-21[2.0A] 1. 텔넷 콘솔 기본 비밀번호 적용.
2. 텔넷 옵션 및 비밀번호 처리관련 버그 수정.
3. WPA 초기 값 버그 수정
4. 시리얼 통신 속도 관련 버그 수정
2015-03-12[1.0A] 최초 배포


P4S-341, P4S-342, P4S-347, P4S-348, P4M-400, P4M-440G, P4H-140, P4H-141, P4H-142, P4H-143, P4H-144, P4H-145, P4H-160, P4H-161 펌웨어 변경이력

배포일[버전] 변경내용
2023-07-21[3.2.0] 1. GD32 MCU 지원
2. PHPoC 엔진 비활성화 기능 지원(비활성화 시 60K mfa 메모리 추가 사용 가능)
3. SNTP 지원(기본 NTP 서버 목록 - pool.ntp.org, time.google.com, time.nist.gov, time.apple.com)
4. RTC calibration 지원(STM32용)
5. AES 모드 추가: CTR128/192/256
6. 시스템 명령어/인자 추가
- aes init ctr enc/dec $key $iv [$counter_len]
- aes crypt $aes $text [$counter]
2020-08-21[2.3.1] - uart0/1 mark parity bug fix
- uart0/1 mutual XOFF pending bug fix
- spi0 mode 0 bug fix
- emac big packet bug fix
- wlan reassoc/disassoc/deauth bug fix
2020-04-01[2.3.0] - net2/3 : ppp net device support
- pkguser lmask : enable network service UI
- fake_ns : mdns host_name bug fix
- mdns new TXT field : device=
- mdns new TXT field : comment=
2020-03-30[2.2.0] - user configurable variable buffer size
- user configurable variable name length
- user configurable string block size
- $GLOBALS support
- tls : certificate chain verification support
- tls : multiple certificate chain path support
- tls : client certificate support
- tls : server name verification support
- tls : host CA support
- PHP_STATE_EXIT bug fix
- exit restart bug fix
2019-10-04[2.1.0] 1. 다중 네트워크 인터페이스 지원(IPv4)
2. TLS 암호화 방식 추가: TLS_ECDHE_ECDSA_WITH_AES_128/256_CBC_SHA
3. TLS 암호화 방식 추가: TLS_ECDHE_RSA_WITH_AES_128/256_CBC_SHA
4. TLS 암호화 방식 추가: TLS_ECHDE_ECDSA_WITH_AES_128_GCM_SHA256
5. TLS 암호화 방식 추가: TLS_ECHDE_RSA_WITH_AES_128_GCM_SHA256
6. TLS 세션 티켓 지원
7. TLS 구 버전 제거: TLS1.0/1.1
8. TLS 암호화 방식 제거: 3DES/RC4
9. TLS 암호화 방식 제거: dsa/dh
10. PXM eio 네트워크 인터페이스 지원(net2/net3)
11. PXM eio 디바이스 지원(edev0/1/2/3)
12. mmap 디바이스 추가: dump0/1/2/3
13. SSH, TELNET 기능 제거
14. 시스템 명령어 제거: seed
15. MDNS 기능 개선: link-up시 IGMP 전송
16. ENVU, UM, NM 사용 개선: set MMAP_FLAG_EXEC (include 가능)
17. 루프 우선순위 기능 지원
2019-05-09[2.0.0] 1. 펌웨어 헤더 변경
2. PXM 헤더 변경
3. 펌웨어 RSA 시그니처 추가
4. 새로운 동작 모드 추가: pkg mode
5. PDB rev_id 변경: 2/1 => 3/3
6. 기본 사용자 추가: pkguser (user3)
7. 사용자 비활성화 기능 지원
8. 기본 비밀번호 기능 지원
9. RSA 시그니처 알고리즘 추가: sha224, sha384, sha512
10. TLS 관련 버그 수정
11. out-of-subnet 로컬 호스트 지원
12. mmap 디바이스 추가: pipe0/1/2/3
13. 전원 LED 동작 추가: power fail시 점멸
14. power fail 이벤트 로그 추가
2018-11-09[1.5.0] 1. 컴파일러 변경
- gcc-arm-eabi-5_2-2015q4 => gcc-arm-eabi-7-2017-q4
2. 다중 실행 PXM 지원
- PIC(position independent code) 지원
- 플래시 코드 지원
- 다중 모듈 실행 지원
3. tls renegotiation 지원
4. SSL3.0 제거
5. mmap 디바이스 추가: /mmap/envm
2018-05-15[1.4.0] 1. 원격 디버거 기능 지원
- PHPoC 사용자 : admin, pdbuser, setup
2. mDNS를 이용한 제품 검색기능 지원
3. HTTPS 지원
4. IPv4 링크 로컬 주소 지원
5. 버튼설정모드 기능 개선
- 이더넷 링크로컬 IP주소 기능 제공
- 이더넷 원격 디버거 기능 지원
6 envs/envc
- ENVC ID 추가 : CRYPTO_ID_UNAME, CRYPTO_ID_PSK
7 mmap 디바이스
- 새로운 디바이스 추가 : /mmap/pipe0/1/2/3a
- 새로운 디바이스 추가 : /mmap/pipe0/1/2/3b
2017-09-29[1.3.1] 1. eap : SSL_STATE_START bug fix
2. string self-assignment bug fix
3. new internal func : trim
4. new hash algorithm : sha256
5. TLS1.1/1.2 support
2017-02-27[1.3.0] 1. 스마트 확장보드 지원
2. P4S-341 UIO0 핀 #20 및 #21 맵핑 변경(USB > GPIO)
3. 일부 버그 수정
2016-07-15[1.2.0] 1. IPv6 지원
2. 새로운 내부함수 추가
- is_bool(), is_int(), is_float(), is_string(), is_array(), str_repeat(), pid_peek(), mktime(), time()
3. data() 내부 함수 개선
4. SPI 통신 개선
5. UART 통신 개선
6. ST 기능 개선
7. TCP 기능 개선
8. 일부 마이너 버그 수정
2015-10-02[1.1.0] 1. 최초 배포


IDIS-200 펌웨어 변경이력

배포일[버전] 변경내용
2016-05-11[1.0A] 최초 배포


PES-2401, PES-2601 펌웨어 변경이력

배포일[버전] 변경내용
2018-12-05[1.2] 1. 신규 제품 추가: PES-2601
2017-07-25[1.1] 1. 새로운 시스템 명령어 추가
- reboot
2017-03-07[1.0] 1. 최초 배포


PES-2402, PES-2602 펌웨어 변경이력

배포일[버전] 변경내용
2018-12-05[1.3] 1. 신규 제품 추가: PES-2602
2. 마이너 버그 수정
2017-07-25[1.2] 1. 새로운 시스템 명령어 추가
- reboot
2017-04-27[1.1] 1. 사소한 버그 수정
2017-03-07[1.0] 1. 최초 배포


PES-2403 펌웨어 변경이력

배포일[버전] 변경내용
2017-07-25[1.1] 1. 새로운 시스템 명령어 추가
- reboot
2. 카운트 값 설정 범위 조정
- ±1000000000(10억)
2017-05-22[1.0] 1. 최초 배포


PES-2405, PES-2605 펌웨어 변경이력

배포일[버전] 변경내용
2018-12-05[1.1] 1. 신규 제품 추가: PES-2605
2017-08-01[1.0] 1. 최초 배포


CSC-HR2 펌웨어 변경이력

배포일[버전] 변경내용
2017-09-05[3.3A] * 최초 배포


PES-2404, PES-2604 펌웨어 변경이력

배포일[버전] 변경내용
2018-12-14[1.3] 1. 버전 표시 오류 수정
2018-12-05[1.2] 1. 신규 제품 추가: PES-2604
2. 마이너 버그 수정
2017-09-13[1.1] 1. 최초 배포


PES-2406, PES-2606 펌웨어 변경이력

배포일[버전] 변경내용
2018-12-05[1.1] 1. 신규 제품 추가: PES-2606
2. 신규 명령어 추가: get txlen
2017-12-27[1.0] 1. 최초 배포


PES-2407, PES-2607 펌웨어 변경이력

배포일[버전] 변경내용
2018-12-05[1.1] 1. 신규 제품 추가: PES-2607
2. 신규 명령어 추가: get txlen
2017-12-27[1.0] 1. 최초 배포


CSW-H85N 펌웨어 변경이력

배포일[버전] 변경내용
2024-03-05[1.2B] 1. 간헐적으로 무선랜 기능이 멈추는 버그 수정
2. 특정 조건에서 TCP 접속 지연 버그 수정
3. 기타 마이너한 버그 수정
2020-09-09[1.2A] 1. 부적합한 deauth패킷 수신 현상 해결
2. IP주소 유효성 검사 로직 개선
3. 기타 사소한 버그 수정
2018-07-04[1.1A] 1. TLS v1.1, v1.2 지원
2. SSL v2.0, v3.0 삭제
2018-03-28[1.0A] 1. 최초 배포


SMG-5400 펌웨어 변경이력

배포일[버전] 변경내용
2022-11-01[3.1.0_p5] 1. Bypass 전송 모드 지원
2. "Query Flow" 설정 여부와 독립적으로 TCP Server/Client 설정 가능
3. 콘솔의 덤프기능 개선
2020-08-21[2.3.1_p4] - 멀티 접속 지원
=> TCP 통신모드는 "Query Flow" 설정에 따라 자동으로 설정
- 상태보기 화면 개선
- MTX/MRX LED 동작 변경 | Modbus/TCP TX,RX -> TCP TX,RX
- 잘못된 Modbus 프레임 검사 로직 개선
2020-01-20[2.2.0_p3] 1. 버그 수정 | STX, SRX LED 동작 오류 수정
2. 버그 수정 | 흐름제어 지원 안 함
3. Unit ID 필터링 기능 추가
2019-08-13[2.0.0_p1] 1. 최초 배포


SMG-5410 펌웨어 변경이력

배포일[버전] 변경내용
2022-11-01[3.1.0_p5] 1. Bypass 전송 모드 지원
2. TCP 접속모드 설정 옵션 추가
3. 콘솔의 덤프기능 개선
4. TCP 세션 관련 설정 개선
2020-08-21[2.3.1_p4] - 멀티 접속 지원
=> TCP 통신모드는 "Query Flow" 설정에 따라 자동으로 설정
- 상태보기 화면 개선
- MTX/MRX LED 동작 변경 | Modbus/TCP TX,RX -> TCP TX,RX
- 잘못된 Modbus 프레임 검사 로직 개선
2020-01-20[2.2.0_p3] 1. 버그 수정 | STX, SRX LED 동작 오류 수정
2. 버그 수정 | 흐름제어 지원 안 함
3. Unit ID 필터링 기능 추가
4. 네트워크로 펌웨어 업그레이드 기능 추가
2019-08-13[2.0.0_p1] 1. 최초 배포
2019-08-13[2.0.0_p2] 1. LED 동작 버그 수정


SMG-5420 펌웨어 변경이력

배포일[버전] 변경내용
2022-11-01[3.1.0_p5] 1. Bypass 전송 모드 지원
2. TCP 접속모드 설정 옵션 추가
3. 콘솔의 덤프기능 개선
4. TCP 세션 관련 설정 개선
2020-08-21[2.3.1_p4] - 멀티 접속 지원
=> TCP 통신모드는 "Query Flow" 설정에 따라 자동으로 설정
- 상태보기 화면 개선
- MTX/MRX LED 동작 변경 | Modbus/TCP TX,RX -> TCP TX,RX
- 잘못된 Modbus 프레임 검사 로직 개선
2020-01-20[2.2.0_p3] 1. 버그 수정 | STX, SRX LED 동작 오류 수정
2. Unit ID 필터링 기능 추가
3. 네트워크로 펌웨어 업그레이드 기능 추가
2019-08-13[2.0.0_p1] 1. 최초 배포
2019-08-13[2.0.0_p2] 1. LED 동작 버그 수정


CSC-HR3 펌웨어 변경이력

배포일[버전] 변경내용
2021-11-30[2.3.1_p4] 1. 펌웨어 버전 업그레이드(2.1.0 > 2.3.1)
2. 동작 안정성 개선
2021-11-26[2.1.0_p3] 1. 원격 연결 기능 추가
2019-10-31[2.1.0_p2] 1. 최초 배포


SIG-5430 펌웨어 변경이력

배포일[버전] 변경내용
2021-08-30[2.3.1_p2] 1. 최초 배포
2020-08-21[2.3.1_p1] 1. 최초 배포


SIG-5440 펌웨어 변경이력

배포일[버전] 변경내용
2021-08-30[2.3.1_p2] 1. 최초 배포
2020-08-21[2.3.1_p1] 1. 최초 배포


SIG-5450 펌웨어 변경이력

배포일[버전] 변경내용
2021-08-30[2.3.1_p2] 1. 최초 배포
2020-08-21[2.3.1_p1] 1. 최초 배포


SIG-5600 펌웨어 변경이력

배포일[버전] 변경내용
2021-08-30[2.3.1_p2] 1. 최초 배포
2020-08-21[2.3.1_p1] 1. 최초 배포


SIG-5431 펌웨어 변경이력

배포일[버전] 변경내용
2023-07-10[3.1.0_p2] 1. 솔내클라우드 v3 접속 지원
2. 데이터 전송 알고리즘 변경
3. 콘솔기능 제거
2021-02-08[2.3.1_p1] 1. 최초 배포


SIG-5441 펌웨어 변경이력

배포일[버전] 변경내용
2023-07-10[3.1.0_p2] 1. 솔내클라우드 v3 접속 지원
2. 데이터 전송 알고리즘 변경
3. 콘솔기능 제거
2021-02-08[2.3.1_p1] 1. 최초 배포


SIG-5451 펌웨어 변경이력

배포일[버전] 변경내용
2023-07-10[3.1.0_p2] 1. 솔내클라우드 v3 접속 지원
2. 데이터 전송 알고리즘 변경
3. 콘솔기능 제거
2021-02-08[2.3.1_p1] 1. 최초 배포


SIG-5601 펌웨어 변경이력

배포일[버전] 변경내용
2023-07-10[3.1.0_p2] 1. 솔내클라우드 v3 접속 지원
2. 데이터 전송 알고리즘 변경
3. 콘솔기능 제거
2021-02-08[2.3.1_p1] 1. 최초 배포


CSE-M53G 펌웨어 변경이력

배포일[버전] 변경내용
2023-11-14[2.3B] 1. 특정 조건에서 공장 초기화 실패 버그 수정
2. 특정 조건에서 TCP 접속 지연 버그 수정
2023-01-17[2.3A] 1. 다중접속 기능 지원 (최대 8채널)
2. AT+PLS 명령 지원
3. RFC2217 기능 개선
4. 기타 사소한 버그 수정
2021-11-25[2.2A] 1. 최초 배포


P5H-151, P5H-152, P5H-153, P5H-154, P5H-155, P5H-156, P5S-351 펌웨어 변경이력

배포일[버전] 변경내용
2022-03-11[3.1.0] 1. 펌웨어 3.1.0 및 이후버전부터 이전 PXM 지원 중단
2. uart/spi/i2c/eio : sys_gate dev_loop 지원
3. UDP 및 SSL 최대 지원 세션 수 변경: 8 => 16
4. FP_ZERO sign 관련 버그 수정
5. system("uptime") 명령 옵션 추가: -m (밀리초)
2021-12-10[3.0.0] 1. 최초 배포


SIG-5560 펌웨어 변경이력

배포일[버전] 변경내용
2022-01-17[3.0.0_p1] 1. 최초 배포


CSC-H61 펌웨어 변경이력

배포일[버전] 변경내용
no result


SCG-5608 펌웨어 변경이력

배포일[버전] 변경내용
2023-12-28[3.1.0_p2] 1. 버그 수정 | Serial RX Idle Time Detection Error
2. 기능 수정 | 콘솔 모듈 업데이트 및 텔넷 설정 환경변수 추가
3. 기능 수정 | SSL 수신 버퍼 크기 변경 (8K -> 17K)
2022-05-02[3.1.0_p1] 1. 최초 배포


SIG-5561 펌웨어 변경이력

배포일[버전] 변경내용
2023-07-10[3.1.0_p2] 1. 솔내클라우드 v3 접속 지원
2. 데이터 전송 알고리즘 변경
3. 콘솔기능 제거
2022-06-22[3.1.0_p1] 1. 최초 배포


CSE-M73G 펌웨어 변경이력

배포일[버전] 변경내용
2023-01-27[1.0B] 1. 일부 현재상태보기 문구 수정
2. RFC2217 기능 개선
3. 마이너 버그 수정
2022-09-02[1.0A] 1. 최초 배포


CIE-H10G, CIE-H12G, CIE-H14G 펌웨어 변경이력

배포일[버전] 변경내용
2023-02-09[1.0B] 1. RFC2217 기능 개선
2. 마이너 버그 수정
2022-12-02[1.0A] 1. 최초 배포


SMG-5620 펌웨어 변경이력

배포일[버전] 변경내용
2023-11-16[3.1.0_p6] 1. 최초 배포